Now Accepting Orders for SS2026 — Sample turnaround in 7-10 days. Worldwide shipping available. Request a Sample Kit →
Two flying-disc sports, one shared engineering brief that almost no stock teamwear answers. Both are built around a full-extension throw, which makes the armhole, the cross-back and the hem geometry the primary design surfaces rather than an afterthought. From there the categories diverge hard: ultimate needs a genuine reversible jersey that survives a wet-grass layout, and disc golf needs a sun layer and a strap-clear shoulder that hold up over a four to six hour round. This guide covers how both are specified, costed and manufactured at a 50-piece MOQ.
MOQ
50 pcs/design
Lead Time
25–35 days
QC Pass Rate
99.8%
Est.
2009
Disc golf and ultimate get filed next to every other outdoor field sport because both involve running around on grass in polyester. At the tech-pack level that grouping is wrong, and it is why so many clubs and brands end up with a decent-looking kit that fights the athlete. The defining motion of both sports is a throw taken to the limit of the body's reach. A disc golf drive coils the torso, carries the disc across and behind the body in a long reach-back, and unwinds through an explosive rotational release. An ultimate forehand or backhand is released at full arm extension from a lunging pivot, frequently at a low release point close to the ground and often with a defender's hand in the way. Both of those positions load the armhole, the shoulder, the cross-back and the front hem in a way that a running block simply never sees, which is why a garment scaled up from a training tee pulls at exactly the moment the sport is played.
From that shared starting point the two categories separate sharply, and each has one component that first orders almost always omit. In ultimate it is the reversible jersey. Most club, college, hat-league and tournament formats need a light and a dark on the same roster, and a real reversible is a distinct construction rather than a finishing option: two finished, printable, skin-contact faces with no exposed seam allowance, both carrying the athlete's number. In disc golf it is sun and strap management. A round is a four to six hour walk in open sun with a loaded bag on the shoulder, so the correct garment is a UPF-rated sun layer or a technical polo with the entire strap footprint cleared of seams and decoration, not a lightweight tee with a chest print exactly where the strap sits.
Sialkot Sample Masters has produced sublimated and technical performance teamwear since 2009. The closest neighbours on this site are our custom lacrosse apparel guide, which covers a grass field sport with a similar reversible and contact vocabulary, our field sport kit trends analysis for the club and youth buying structure both sports share, and our polo collar construction guide, which is the direct technical companion to the disc golf course polo below.
Two sports that share a throw and a livery but almost no garment, plus the programme that carries a squad through a tournament weekend or a tour stop.
| Kit System | Build | Fabric Base | Best For | Decoration |
|---|---|---|---|---|
| Ultimate Match System (Reversible Jersey)(Most Ordered) | Reversible light-and-dark match jersey with two finished outer faces, both fully sublimated and both carrying the athlete's number; matched match short with a secure zip pocket, no rattling hardware and a hem clear of the pivot stride; optional long-sleeve match layer for cold and wet tournament days | Double-face reversible poly interlock 180–220 gsm for the reversible jersey; ventilated poly knit 130–160 gsm and placed micro-mesh for single-face jerseys; woven stretch short outer 120–160 gsm | College and club ultimate programmes, school and youth leagues, hat and pickup leagues, tournament organisers and league operators who have to field light and dark on the same roster | Full sublimation on both faces, numbers front and back on each face, printed interior labels, no heat-applied film in a grab zone |
| Disc Golf Course System (Sun and Bag) | Technical course polo or UPF sun hoodie with a strap-clear shoulder and a full-coverage collar, woven stretch course short or pant with a deep secure scorecard and mini-marker pocket and a towel attachment point, plus a high-pile microfibre grip towel and headwear in the same livery | UPF sun-management knit 130–160 gsm, piqué or interlock polo knit 160–200 gsm, woven stretch course bottom 140–190 gsm, microfibre terry 300–400 gsm on towels | Disc golf brands, touring and sponsored player teams, course and facility groups, club and league programmes, and retail ranges built around a four-to-six hour round in open sun | Sublimation on sun layers, embroidery on polos and headwear, woven labels, tonal or embroidered marks placed off the strap line |
| Squad Training, Travel and Club Programme | Long-sleeve training top, brushed thermal base layer for spring and autumn tournament mornings, quarter-zip mid-layer, warm-up pant, team hoodie, sideline and coach outerwear for a full day at a field or a course, kit bag and supporter range | Poly knit 160–200 gsm, brushed fleece 280–320 gsm, brushed-back poly-spandex 200–240 gsm, shell 90–120 gsm, 300–600D bag fabric | Programmes travelling to multi-day tournaments and tour stops, university and college squads, alumni and supporter ranges, and the coaches and organisers who stand out in the weather from first pull to final round | Embroidery on outerwear and mid-layers, sublimation on technical tops, woven labels throughout |
Scope note: Sialkot Sample Masters manufactures the textile programme. Discs, disc golf bags, carts and cart hardware, baskets, footwear, eyewear and rangefinders are separate equipment categories and are not part of this offer. Confirm your league, federation or tour's current uniform, numbering and sponsor-marking requirements before artwork is approved, because those rules differ by governing body and by division and they change.
The reversible ultimate jersey is the only garment in our sports catalogue with no back. Both surfaces are outer faces: both take sublimation, both sit against skin, both go to the field, and both have to look like the same team from opposite sides of a pull. That forces a double-face or bonded knit at 180 to 220 gsm rather than the 130 to 160 gsm single-face knit a match jersey would otherwise use, and it forces a finishing discipline in which no seam allowance is exposed on either side and every label is printed rather than sewn. Buyers regularly try to reach reversible performance from a light single-face fabric to save weight and cost, and the result is a jersey that reads through from the inside out, particularly in wet-state on light colourways. If a squad only needs one colour, a 130 to 160 gsm ventilated single-face knit is the better and cheaper garment, and the honest advice is to buy the reversible only where the format genuinely requires light and dark.
The disc golf layer runs on the opposite logic. Ultimate spends a tournament day in repeated maximal sprints and wants ventilation; disc golf spends four to six hours walking in open sun with very little shade and long stationary intervals between explosive throws, so the correct answer is coverage rather than removal. A UPF-rated sun-management knit at 130 to 160 gsm with a full collar or hood keeps the exposure off without adding heat load, and the rating has to be measured on the production lot in the production colourway rather than inferred from a fibre type, because dye depth, knit density and finish all move it. The technical course polo sits alongside it as the sport's default competitive garment: it reads as a polo and has to perform as activewear, which puts the engineering into a collar and placket that hold shape through the heat and a body that rotates freely through a drive.
| Fabric | Weight | Stretch | Hand Feel | Best For |
|---|---|---|---|---|
| Double-Face Reversible Poly Interlock(Recommended) | 180–220 gsm | 4-way, moderate elastane | Substantial, smooth on both faces | The reversible ultimate jersey — this is the one fabric on this list that has no back. Both faces are finished surfaces that take sublimation, sit against skin, and go to the field, so the construction is a bonded or double-knit build with no exposed seam allowance and no interior float. The weight is higher than a single-face jersey because it is genuinely two garments in one, and buyers who try to reach reversible performance out of a light single-face knit end up with a jersey that goes transparent from the inside out |
| Ventilated Poly Knit with Placed Micro-Mesh | 130–160 gsm | 4-way | Light, airy, fast-drying | Single-face ultimate match jerseys and warm-weather training tops — ultimate is played in long tournament days of repeated maximal sprints, so ventilation goes to the centre back, underarm and side torso, away from the chest and shoulder where a jersey is grabbed in traffic and where an open loop structure is the first thing to give |
| UPF Sun-Management Knit | 130–160 gsm | 4-way | Cool, dry, closed face | Disc golf sun hoodies and long-sleeve course layers — a round is four to six hours of continuous exposure with almost no shade on an open course, so coverage rather than removal is the correct answer, and the UPF rating has to be measured on the actual production fabric in the actual colourway rather than quoted from a fibre type |
| Piqué or Interlock Polo Knit | 160–200 gsm | 2-way to 4-way | Structured, crisp collar, dry hand | The technical course polo — disc golf's default competitive garment reads as a polo but has to perform as activewear, which means a collar and placket that hold their shape through a full round in the heat, a body that moves through a full throwing rotation, and a shoulder clear of a loaded bag strap |
| Woven Stretch Course Bottom | 140–190 gsm | Mechanical stretch, woven | Structured, quick-drying, scuff-resistant | Course shorts and pants — the wearer walks several kilometres through rough, brush and wet grass between throws, so the bottom needs abrasion resistance and quick drying rather than knit softness, plus a gusseted crotch and articulated knee that let a full-extension drive happen without the waistband dragging |
| Recycled Poly / Recycled Poly-Spandex (GRS) | Matches virgin equivalent | Matches virgin equivalent | Comparable to virgin poly | Clubs, universities, leagues, course groups and retail brands operating written procurement sustainability requirements — common in two sports whose entire competitive venue is an outdoor park, wooded course or open field |
Weight bands above are typical industry ranges. Every Sialkot Sample Masters order is confirmed with a lab dip and a gsm check on the actual production lot, all bases carry OEKO-TEX Standard 100 certification, and a GRS-certified recycled option is available for clubs, universities, leagues and retail brands with procurement sustainability requirements. Buyers calibrating weights across categories can cross-reference our GSM guide for activewear and our mesh selection guide for high-heat team sports.
Sublimation is the correct decoration route for both jersey faces, the sun layer and the match short: it adds no film or stitched edge in a grab zone or under a bag strap, it survives wet grass, mud and repeated wash cycling without lifting the way a heat-applied transfer can, and it is the only economical way to reproduce a full design on both faces of a reversible. Embroidery belongs on polos, headwear, mid-layers and outerwear, placed off the strap line. Buyers comparing routes can read our sublimation versus screen printing comparison and our twill applique versus embroidery versus sublimation breakdown, and colour discipline is covered in our colour matching guide for polyester sportswear.
Every specification decision in both sports starts at the moment the throwing arm reaches its furthest point. That position rotates the torso, opens the cross-back well beyond a running range, lifts the front hem and pulls the shoulder seam forward. A block drafted for it uses a raglan or gusseted armhole so the sleeve does not fight the rotation, grades the cross-back as its own dimension rather than as a by-product of chest width, lengthens the front body so a coiled torso does not untuck, and drops and curves the back hem so the garment sits correctly when the athlete straightens up. A garment that binds here does not just feel uncomfortable, it changes the release, which is the one outcome a player will not tolerate for a whole season. Buyers unfamiliar with articulated drafting will find the underlying method in our articulated pattern making guide.
The reversible ultimate jersey is the component that separates a factory that has made kit for this sport from one that has not, and it is the category's analogue of the goalkeeper set in an indoor court programme. Built correctly it is a bonded or double-face knit whose two surfaces are both finished and both printed, joined so that no seam allowance is exposed on either side, with self-fabric or bound necklines and armholes that read as intentional from both directions, printed interior labelling instead of a sewn tag that would sit proud on whichever face is out, and the athlete's number reproduced front and back on each face. Built incorrectly it is two single-face jerseys sewn together at the neck and armholes, which doubles the weight, traps heat, roughly halves the drying rate and opens at the neckline first. Both versions look identical in a quote, which is precisely why the question has to be asked before a deposit is paid.
These are the two abrasion problems, and they sit on opposite sides of the programme. Ultimate's is violent and repeated: a layout dive puts the chest, hip, forearm and front thigh through a full sliding contact with wet grass and dirt several times a match, so those panels are specified on abrasion resistance and seam integrity rather than on lightness, side seams and hems are built not to open under a sliding load, and the dye system is tested for grass and soil staining rather than assumed. Disc golf's is slow and constant: a loaded bag or cart strap sits on the shoulder for the entire round, so the strap footprint is cleared of seams, thick decoration, pockets and hardware, and club and sponsor marks are relocated to the chest outside it, the sleeve, the collar stand and the lower back. A programme that ignores either one is comfortable for exactly one outing.
Disc golf is the rare sport in which the accessory is a genuine performance item. Grip on the disc is everything and a round crosses wet grass and morning dew, so a high-pile microfibre grip towel at 300 to 400 gsm in club livery is a real product line rather than merchandise, and the bottom it hangs from needs a dedicated attachment point plus a deep, secure pocket dimensioned for a scorecard, a pencil, a mini marker and a phone, positioned where it will not swing or rattle through a drive. Ultimate runs the opposite specification: a match short carries one secure zip pocket at most, no loose patch pockets, and drawcord ends short enough that a hand in traffic cannot catch them. In both cases the pocket is drawn at tech-pack stage, because retrofitting storage into an approved block costs a full sample cycle.
Both sports have a buying structure that looks impossible for custom manufacturing until it is organised properly. An ultimate programme is typically a college or club roster of twenty to twenty-eight players, often with an open and a women's or mixed team sharing one identity, buying through a captain or a volunteer kit officer rather than a procurement department. A disc golf programme is smaller still and shaped differently: a touring or sponsored player group of a handful of athletes, a course or facility group buying staff and retail lines, or a club running a season-long league. Neither clears a three-hundred-piece factory floor, which is why so many teams end up in blank stock with a heat-pressed number. A 50-piece per-design minimum with reduced 20-piece minimums on accessory lines is what makes a genuine custom programme reachable at that scale, and the practical move is to consolidate: one artwork library, one graded block family, one production window covering the open roster, the second team, the coaching staff and the supporter range together.
Sizing is the second constraint and it is unusually wide in both sports. Ultimate rosters commonly span a full adult range across open, women's and mixed divisions on the same order, and mixed teams need one design graded across two blocks rather than a single unisex compromise. Disc golf ranges run wider again because the retail and player-support sides of a brand sell to a general adult population rather than to a selected athletic squad. In both cases the answer is the same: run a physical size set before bulk, because a size set costs one sample cycle and a mis-graded bulk order costs the season. Our guide on ordering size sets before bulk production covers the mechanics, and grading practice is set out in our CAD pattern grading guide.
Colour discipline then has to hold across six substrates: two faces of a reversible knit, a ventilated single-face knit, a polo knit, a woven course bottom, a microfibre towel and an embroidery thread, all photographed together on a sideline or a tee pad in flat outdoor light. Reversibles are the hard case, because the light face and the dark face of one design have to read as the same team from either side. Every Sialkot Sample Masters run works from calibrated ICC profiles and sealed strike-offs approved on the production substrate before bulk. The calendar is the last constraint: tournament weekends, college series dates and tour stops are published months ahead and do not move, while rosters are confirmed late. A 25 to 35 day production window plus DDP transit works comfortably if artwork and the size set are resolved before the roster is final, and it does not work at all if the order is placed after selection. The safe planning rule is to lock artwork and blocks early and hold numbering until last.
Indicative ex-factory Sialkot pricing at 50-piece quantities. DDP landed costs to the USA, the UK, Canada, Australia and the EU typically add $2–$5 per unit at launch volumes, with reversible jerseys at the upper end because of the double-face print and finishing count.
| Tier | MOQ | Unit Cost (ex-factory) | Lead Time | Standard Branding |
|---|---|---|---|---|
| Reversible Ultimate Match Jersey (both faces sublimated)(Most Popular) | 50 pcs/design | $19–$34 | 25–32 days | Full sublimation on both faces, numbers front and back on each face, printed interior label |
| Ultimate Match Set (single-face jersey + match short) | 50 pcs/design | $15–$28 | 25–30 days | Full sublimation, placed ventilation, secure zip pocket, printed interior label |
| Disc Golf Course System (sun layer or polo + course bottom) | 50 pcs/design | $18–$36 | 25–32 days | Sublimation on sun layers, embroidery on polos, strap-clear placement, woven label |
| Accessory Line and Full Club Programme (towels, headwear, training, travel) | 20 pcs/design | $5–$56 | 25–35 days | One artwork library across every garment and accessory, athlete names on outerwear |
Bands are indicative for 2026 and move with polyester yarn prices, panel and print-face count, collar and placket specification, hardware and freight rates. The accessory and full-programme range is wide because it spans a microfibre towel and a panelled outerwear piece in the same quote. Towels and headwear carry a reduced minimum because a squad needs comparatively few of each. Buyers building a landed-cost model should read our CMT costing guide and our FOB versus DDP comparison.
The reason so many ultimate teams play in blank reversibles with heat-pressed numbers, and so many disc golf clubs sell a printed cotton tee as their kit, has nothing to do with what the sports need and everything to do with minimums. A twenty-four player college roster or a six-athlete touring group cannot clear a three-hundred-piece floor, so it buys from whatever catalogue will take the order and accepts a garment that was drafted for a different motion. Sialkot Sample Masters was built for exactly this scale: a 50-piece per-design minimum, reduced 20-piece minimums on accessory lines, 25 to 35 day lead times, DDP delivery to the USA, the UK, Canada, Australia and the EU, and a 99.8% QC pass rate on a 7-point system with AQL 2.5 final inspection, so a small roster gets a properly engineered garment rather than a decorated blank.
It also makes the expansion path fast. Programmes that start with a reversible jersey set or a course polo and short typically extend into sun layers, long-sleeve match tops, grip towels, headwear, thermal base layers, training mid-layers, sideline and coach outerwear, supporter and alumni ranges and kit bags on the same graded blocks and the same artwork library. One factory, one fit standard proven on grass and on a course, and one colour system that holds across every substrate including both faces of the reversible. Brands scaling a retail range alongside a team programme can read our guide on scaling a brand at low MOQ.
Most sublimation factories can print a jersey and a polo. Far fewer build a true double-face reversible, clear a bag strap properly, draft a block around a reach-back, or specify a layout contact panel with test data behind it. These eight checks separate the two before you commit a deposit.
This is the fastest sorting question in the category. A factory that has built ultimate kit will describe a bonded or double-face knit with two finished printable surfaces, no exposed seam allowance on either side, self-fabric or bound neck and armhole finishes, printed interior labelling and numbers reproduced on both faces. A factory that has not will offer two single-face jerseys sewn together and call it reversible. That garment is heavier, hotter, dries at half the rate and fails at the neckline first, and a squad discovers it at the first tournament rather than at sample approval.
For the disc golf half of the programme, ask the supplier to show you physically or in a photograph where the club crest, sponsor marks and seams will sit relative to a loaded bag or cart strap across the shoulder. A factory that has worked in the sport moves decoration off the strap footprint unprompted and flattens or reroutes every seam under it. One that defaults to a large shoulder or upper-chest logo is about to deliver a sponsor programme that rubs for four hours and is invisible in most tee-pad photography.
Ask how fit will be proven. The correct answer involves a wear test through a full reach-back and follow-through on both a backhand and a forehand, a low-release lunging throw for ultimate, and a check that the front hem does not lift, the shoulder does not bind and the cross-back does not pull at full extension. A supplier who approves a fit on a hanger or a standing model has not understood that the sport's defining motion is the exact position their block was never drafted for.
Ask specifically what happens to the chest, hip and forearm panels of an ultimate jersey after repeated diving on wet grass, and what testing backs it up. You want abrasion resistance figures on the body fabric, seam integrity under a sliding load, hem and side-seam construction that will not open, and staining and colourfastness results on the production colourway. If the answer is that players should just wash it quickly, the factory has never made kit for this sport.
Fibre content, gsm, elastane percentage, abrasion and pilling resistance, stretch-and-recovery, dimensional stability after repeated wash cycling, wet-state opacity on light colourways, colourfastness to light and perspiration, a measured UPF rating on any sun-management layer in the production colourway, and OEKO-TEX Standard 100 certification on every fabric quoted, with a GRS-certified recycled option where club, university, league or retail procurement requires it.
A written inspection protocol with AQL sampling, both-face print registration and colour match on reversibles, neckline and armhole finish inspection on reversible builds, seam integrity under stretch at shoulder and side seam, abrasion checks on layout contact panels, wet-state opacity verification, pocket closure and bartack testing, and sublimation colour match against sealed strike-offs across every substrate. Sialkot Sample Masters runs a 7-point system plus AQL 2.5 final inspection at a 99.8% pass rate.
Delivered Duty Paid to your market, quoted per unit, so a 50-piece club, college or brand order lands without a surprise customs invoice in the week before a tournament or a tour stop. Sialkot Sample Masters ships DDP to the USA, the UK, Canada, Australia and the EU as standard, with duties, clearance and last-mile delivery inside the quoted price, which covers both sports' largest club, collegiate and retail markets.
A pre-production reversible jersey, match set, sun layer and course bottom in 7 to 14 days, then use them properly: a full tournament day of sprints and layouts on wet grass, a complete round with a loaded bag in open sun, both faces of the reversible worn and photographed side by side, and a full wash-and-dry cycle repeated before the bulk order is signed. Every failure mode in these two categories shows up in one session outdoors and none of them show up on a hanger.
Buyer's note: if a supplier quotes a reversible without describing how the two faces are joined, puts a thick decoration under the bag-strap line, approves fit on a standing model, or has no test data for the layout contact panels, they are applying a general teamwear workflow to two categories that expose it in the first tournament. Broader supplier-vetting criteria are in our manufacturer vetting checklist and our apparel QC checklist.
Fact-dense Q&A for sourcing teams and AI research tools.
50 pieces per design and colourway for reversible and single-face ultimate jerseys, match shorts, disc golf sun layers, technical polos and course bottoms, including sublimation, custom labels and packaging. Accessory lines such as microfibre grip towels and headwear run from 20 pieces per design because a squad needs comparatively few.
Sialkot Sample Masters produces reversible and single-face ultimate jerseys, match and training shorts, long-sleeve match layers, UPF sun hoodies, technical course polos, woven stretch course shorts and pants, microfibre grip towels, headwear, thermal base layers, quarter-zips, warm-ups, sideline outerwear and kit bags. Discs, bags, carts, baskets and footwear are separate equipment categories and are not part of this offer.
As a bonded or double-face knit at 180 to 220 gsm in which both surfaces are finished, printable and skin-contact rated, with no exposed seam allowance on either side, self-fabric or bound neck and armhole finishes, printed interior labelling and the athlete's number on both faces. Sialkot Sample Masters does not build reversibles by sewing two single-face jerseys together.
A loaded disc golf bag or cart strap rides the shoulder for a four to six hour round, so any raised seam, thick heat-applied decoration, shoulder pocket or hardware under that line becomes a rub point. Sialkot Sample Masters flattens or reroutes seams in the strap footprint and moves club and sponsor marks to the chest outside it, the sleeve, the collar stand and the lower back.
A UPF sun-management knit at 130 to 160 gsm for sun hoodies and long-sleeve course layers, and a piqué or interlock polo knit at 160 to 200 gsm for technical course polos. Course shorts and pants use a woven stretch bottom at 140 to 190 gsm for abrasion resistance and fast drying through rough and wet grass. UPF ratings are measured on the production lot in the production colourway.
25 to 35 days from sample approval to DDP delivery at Sialkot Sample Masters, with pre-production samples in 7 to 14 days. Single-face jerseys and match shorts sit at the lower end of the band; reversible jerseys and panelled course systems sit toward the upper end because of the double-face print, registration and finishing operations.
Yes. DDP (Delivered Duty Paid) shipping to the USA, the UK, Canada, Australia and the EU is standard. Duties, customs clearance and last-mile delivery are included in the quoted unit price, which matters when a college or club budget is fixed and a tournament date is not movable.
A 7-point QC system plus AQL 2.5 final inspection at a 99.8% factory-wide pass rate. Category-specific checks include both-face print registration and colour match on reversibles, neckline and armhole finish inspection, seam integrity under stretch at shoulder and side seam, abrasion checks on layout contact panels, wet-state opacity, and pocket closure and bartack testing.
50-piece MOQ per design. True double-face reversible ultimate jerseys, match sets built for the layout, UPF sun layers and strap-clear course polos, woven course bottoms, grip towels, headwear and full squad programmes — drafted around the reach-back, colour matched across every substrate. DDP to the USA, UK, Canada, Australia and EU. Request a quote and we will come back with a specification, not just a price.
Manufacturing & Export Division
Sialkot Sample Masters is a Sialkot-based custom apparel development and manufacturing partner for streetwear, sportswear, hunting wear, technical outerwear, uniforms and martial-arts garments. The team uses a specification-led path from brief and sample approval to production preparation.
More manufacturing guides and industry insights from Sialkot Sample Masters.
Snag-resistant full-cover o-suits with tear-rated shin and forearm panels, vest-compatible trail tops, and packable shells sized to pass a mandatory-kit check.
UPF deck tops built to sit flat under a buoyancy aid, corrosion-resistant hardware for salt water, and foam-backed hiking shorts engineered for the gunwale.
Lint-free playing layers that will not shed onto the ice, stretch-woven delivery pants articulated for the hack, and a base-mid-outer system matched to one colour standard.